Exoracing Silicone Hose Kit For Honda Civic B16 B18 6pc

Fitment And Compatibility

This kit is for compatible Honda Civic and Integra B16/B18 coolant and heater hose layouts. It includes six reinforced silicone hoses and the clamp kit needed to replace the matching original hoses.

• Fits: B16/B18 setups that match the six hose locations and Honda references listed below.
• Check first: engine-swapped cars, imported cars, turbo builds, aftermarket radiators and modified coolant/heater routing should compare the hose layout before ordering.
• B18C4 note: This kit does not fit B18C4 out of the box. It may be made to fit with modification, but it should not be treated as direct fitment.
• Does not fit: D-series, K-series, H-series or custom coolant routing as a complete hose kit.

If you are not sure whether your B-series hose layout matches, contact us before ordering.

Why Should You Use An Exoracing B16/B18 Silicone Hose Kit?

Old Honda rubber coolant hoses can harden, crack and swell after years of heat cycles, coolant exposure and engine-bay temperature. A failed coolant or heater hose can quickly lead to coolant loss, overheating and avoidable engine damage.

The Exoracing B-series silicone hose kit upgrades the matching original hoses to reinforced 4-ply silicone. The kit includes six hoses plus a full 304 stainless steel worm drive clamp kit, so you can refresh the main B16/B18 hose set without reusing tired clamps.

The black outer with purple inner layer gives a clean engine bay finish while adding resistance to heat, UV, water and ageing. It is a practical upgrade for road cars, track cars, B-series swaps and restored Civic or Integra engine bays.

For fitting help, read our silicone hose kit installation guide. For more cooling and hose products, browse the Exoracing heat management collection.

Purchase Includes:

• 6 x Exoracing B-series reinforced silicone hoses
• 1 x Exoracing 304 stainless steel worm drive clamp kit
• 1 x Exoracing Lifetime Warranty

Features:

• Designed for compatible Honda Civic / Integra B16 and B18 hose layouts
• Replaces the six listed coolant and heater hoses
• Includes a 304 stainless steel worm drive clamp kit
• Manufactured from high-quality 4-ply reinforced silicone
• 4.5mm wall thickness
• Working pressure: 85 PSI
• Burst pressure: 245 PSI
• Operating temperature range: -65°F/-54°C to 500°F/260°C
• Black outer finish with purple inner layer
• Includes Exoracing lifetime warranty

Exoracing Honda B16/B18 Silicone Hose Kit Installation Guide:

Install this kit while the engine is cold and the coolant system is drained.

1. Make sure the engine is completely cold before opening the cooling system.
2. Safely raise the car if extra access is required and place a drain pan under the radiator drain point.
3. Remove the radiator cap, drain the coolant and dispose of old coolant responsibly.
4. Lay out the six silicone hoses and match each hose to the location table below.
5. Remove one old hose at a time and fit the matching Exoracing silicone hose in the same location.
6. Make sure each hose is fully seated on the pipe neck before tightening the supplied 304 stainless clamp.
7. Do not over-tighten clamps, as excessive clamp force can damage silicone hoses.
8. Refill the cooling system with suitable coolant and bleed the system fully.
9. Run the engine up to temperature, check for leaks, then recheck the coolant level once the engine cools.

Installation difficulty: moderate DIY. Professional installation is recommended if you are not confident in draining and bleeding a cooling system.

Technical Specifications:

Exoracing B-Series Silicone Hose Kit Location Table:

Use this table to match each silicone hose to the correct B-series coolant or heater hose location. These Honda references are included to help you cross-check the layout before ordering or fitting.

Frequently Asked Questions

Will this fit my Honda Civic or Integra B-series?

It is designed for B16/B18 hose layouts that match the six listed hose locations. Compare your existing hoses before ordering if your car is swapped, imported or modified.

Will this fit a B18C4?

Not out of the box. The current fitment note is that B18C4 requires modification, so do not buy this as a direct-fit B18C4 hose kit.

Does this include clamps?

Yes. The kit includes a 304 stainless steel worm drive clamp kit, so you do not need to reuse old coolant hose clamps.

Does this include every hose in the engine bay?

No. It includes the six coolant and heater hoses listed in the location table. Compare your hose layout before ordering if your car has custom routing.

When should I fit this kit?

The best time to fit it is while the coolant system is already drained, such as during radiator replacement, B-series swap work, coolant service or engine-bay refresh work.

Notes:

• This kit is for matching Honda Civic / Integra B16/B18 hose layouts.
• This kit will not fit B18C4 out of the box. It may be made to fit with modification, but it is not a direct fitment.
• Engine-swapped, imported, turbocharged or modified cars should compare hose routing before ordering.
• Install only when the engine is cold to reduce the risk of burns from hot coolant.
• Bleed the cooling system fully after installation and check for leaks after the first heat cycle.
• Professional installation is always recommended.

Official product information supplied by Exoracing.